Torque Multistrada

From Noah.org
Revision as of 04:13, 20 October 2006 by Root (talk | contribs)
(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)
Jump to navigationJump to search

Ducati Multistrada Frame torque settings

                                                              * critical point for dynamic safety.
                                                                Tightening torque tolerance must be: ± 5% Nm.

Part | Thread (mm) | Nm ~±10% tolerance | Notes

Side stand

Side stand pin 10x1.25 20 Stand pin safety nut 10x1.25 25 Stand assembly to engine screws 10x1.5 36 LOCK 5 Stand sensor retaining screw 6x1 10

Wiring guide screw 6x1 10

Chain, Front chain sprocket

Sprocket nut 25x1.5 186* GREASE B Sprocket cover retaining screw 6x1 8

Sprocket cover retaining screw (plate) 5x0.8 6

Light units

Number plate holder and cat's eye bracket to 6x1 6 LOCK 2 number plate holder mount screw

Cat's eye to cat's eye bracket nut 4x0.7 2 Tail light to mount retaining screw (center) 5x0.8 1.5 Tail light to mount retaining screw (sides) 5x0.8 4 Headlight to mount screw 6x1 10

Rear light unit mount retaining screw 6x1 8

Instrumentation

Instrument panel fixing nut 5x0.8 4

Front fork

Fork bottom screw 8x1.25 19* GREASE B

                                                                    Sequence1-2-1

Bottom yoke screw 8x1.25 22* GREASE B

                                                                    Sequence1-2-1
                                                                                             

Steering head screw 8x1.25 22* GREASE B

                                                                    Sequence1-2-1

Steering bearing ring nut 35x1 30* GREASE B Splashguard to bottom yoke screw 5x0.8 5 LOCK 2

Steering lock check nut 8x1.25 18 LOCK 2

                                                                    (apply Loctite to nut
                                                                    thread only)

Brake hose bracket retaining screw 6x1 10

Electric system

Voltage regulator to frame screw 6x1 10 Immobilizer antenna Place between antenna

                                                                    and switch cover LOCK
                                                                    9
                                                                                             

Speed sensor retaining screw 6x1 10 LOCK 2 Right switch retaining screw 3.5 Contactor cable nut 4 Oil cooler hose guide plate to battery mount 5x0.8 4 LOCK 2 screw Battery retaining screw 5x0.8 5

ECU retaining screw 6x1 10 Batter y mount to frame screw 6x1 10 Ground cable to engine casing screw 6 Fuse retaining screw 5x0.8 5 Cable guide to exhaust fixing nut 6x1 8 Horn retaining screw 8x1.25 24 LOCK 2 Fuel sensor retaining screw 6x1 10 Coil retaining screw 5x0.8 5 Contactor cable to starter motor fixing nut 6 ECU retaining screw 6x1 10 Horn rotation nut 12x1 15

Front brake

Front brake caliper retaining screw 10x1.25 43* GREASE B Front brake master cylinder retaining screw 6x1 10 Sequence 1(UP)-2-1 Front/Rear brake disc retaining screw 8x1.25 25 LOCK 2 Brake bleed nipple 6x1 10 Front/Rear brake bleed connector 10x1 23

Rear swingarm

Swingarm pivot nut 18x1.5 75* GREASE B Eccentric hub to swingarm clamping screw 12x1.25 31* GREASE B -

                                                                    Sequence1-2-1

Caliper mounting plate locating pin 12x1.25 33* LOCK 5 Chain sliding shoe retaining screw (upper and 6x1 10 LOCK 2 lower) Chain guard retaining screw (upper and lower) 6x1 10 LOCK 2 Brake hose clips to swingarm screw 5x0.8 5 Mudguard to swingarm screw 6x1 10 Heat guard to swingarm screw 6x1 10 LOCK 2

Rear brake

Brake bleed nipple 6x1 10 Front/Rear brake bleed union 10x1 23 Rear brake caliper screw 8x1.5 25* GREASE B Rear brake actuating rod nut 6x1 8 Brake pedal adjusting dowel fixing nut 2.3 Rear brake light switch fixing nut 5 Brake lever clamp to footpeg bracket screw 6x1 10 Master cylinder retaining screw 6x1 10 LOCK 2 Fluid reservoir retaining screw 2 LOCK 2

Handlebar, Clutch control

Handlebar clamp retaining screw 8x1.25 20* GREASE B

                                                                    Sequence1-2-1

Counter weight retaining screw 6x1 10 Clamp to steering head screw 10x1.5 45* LOCK 2 Clutch transmission unit retaining screw 6x1 10 Sequence1-2-3-1 Throttle control retaining screw 6x1 6 Sequence1-2-1


Rear shock absorber

Shock absorber/linkage to swingarm screw/ 10x1.25 45* GREASE B nut Shock absorber to rocker arm screw 10x1.25 45* GREASE B

Linkage to rocker arm screw 10x1.25 45* GREASE B Suspension rocker arm to frame screw 10x1.25 45* GREASE B Adjuster to mount screw 6x1 10 Adjuster mount to frame screw 6x1 10 LOCK 2

Linkage joints fixing nut 12x1.25 36

Front mudguard

Complete mudguard to front fork screw 6x1 3 LOCK 2 Mudguard (front to rear section) jointing 5x0.8 2.5 LOCK 2 screw

Footpegs and levers

Fixing nut for UNIBALL between gearbox rod 6x1 10 Lock out rotation at and link rod screw end

Heel guard to rear footpeg screw 5x0.8 6 Gear change pedal retaining pin 8x1.25 23 LOCK 2 Sprocket cover plate retaining screws (on left 5x0.8 8 footpeg) Footpeg bracket to engine casing screw 10x1.5 36

(shorter) Footpeg bracket to engine casing screw 10x1.5 36 (long) Footpeg bracket to frame special screw 12x1.25 30 GREASE B

Brake lever retaining screw 6x1 10 Rear footpeg bracket retaining screws 8x1.25 24 Gearbox actuating rod retaining screw 6x1 10 Gearbox clamp retaining screw 6x1 10 LOCK 1

Rear mudguard

Rear chain sprocket splashguard fixing nut 6x1 8 Splashguard bracket retaining screw 5x0.8 5 LOCK 2

Front wheel

Front wheel shaft fixing nut 25x1.25 63* GREASE B (grease

                                                                    under head and thread
                                                                    of nut and wheel shaft)

Front brake disc retaining screw 8x1.25 25* LOCK 2

Rear wheel

Rear wheel left nut 33x1.5 156* GREASE B Rear wheel right nut 38x1.5 177* GREASE B Drive pegs retaining screw 6x1 11* LOCK 2

Rear chain sprocket nuts 10x1.25 48* GREASE B Rear brake disc retaining screw 8x1.25 25* LOCK 2

Fuel tank

Plastic tank flange cover retaining screw 6x1 10

Plastic tank flange retaining screw 6x1 10

Filler plug retaining screws 5x0.8 5 Fuel sensor 6x1 10 Front bracket retaining screw (RH/LH) 6x1 10 LOCK 2 Side fairing mounting peg 6x1 1.5 LOCK 2 Breather and drain hose inserts 7x1 2 Roll-over valve retaining screws 5x0.8 2.5 Mudguard retaining screw under tank 5x0.8 4 LOCK 2 Latch mount retaining screws 6x1 10 Liquid recovery hose fitting 10x1.5 4 LOCK 2 Liquid recovery hose clip 1 Liquid recovery reservoir retaining screws 6x1 6 Side panels centering peg 6x1 3 Passenger seat bracket retaining screws 5x0.8 2.5 Fuel tank to frame retaining screws 6x1 5 LOCK 2 Fuel tank pad screws 8x1.25 22 Fuel tank central pad screw 8x1.25 16 Fuel tank flange special retaining screw 6x1 10 Fuel tank flange cover nut 5x0.8 6

Exhaust

Manifold to head fixing nut 8x1.25 24 CO take-up point blanking cap 10x1.25 25 Heat guard to horizontal pipe screw 6x1 10 Horizontal pipe to presilencer flange screws 6x1 10 Presilencer-to-silencer connector pipe clamp 8x1.25 20 Presilencer to engine casing bracket screw 6x1 10 Silencer central retaining screw 8x1.25 24 Tail heat guard to silencer screw 6x1 8

Seat

Rider seat retaining screw 6x1 10 Helmet cable spring catch self-tapping screw

Frame

Engine mounting bolt nut 12x1.25 60* GREASE B Front subframe to frame screw (sides) 8x1.25 24 LOCK 2 Front subframe to frame screw (center) 8x1.25 24 Seat lock retaining screw on badge 6x1 6 Seat lock latch retaining screw 6x1 8 Luggage rack retaining screw 6x1 10 LOCK 2 Grab handle retaining screw 6x1 10* LOCK 2 Fuel tank adjusting nut 8x1.25 22 Mobile subframe retaining screw 8x1.25 18 Headlight mount to subframe screw 6x1 10 Ignition switch retaining screw 6x1 10 LOCK 2

Oil cooler nipple on cooler 14x1.5 23 Lock out rotation at

                                                                    cooler end with LOCK 1

Oil cooler nipple on engine 14x1.5 23 LOCK 2

Oil cooler retaining screw 6x1 10 Oil hose fitting with twin seal on cooler 16x1.5 18* Lubricate with engine

                                                                    oil

Oil hose fitting with twin seal on engine 16x1.5 18* Lubricate with engine casing oil

Thermistor fixing 10 LOCK 4 Oil hose guide plate retaining screw 5x0.8 5

Air intake, Oil breather

Stud bolt to airbox fixing 6x1 6

Coils to airbox screw 5x0.8 5 Nipple for <stepper motor> 8 LOCK 2 Airbox to frame screw 6x1 10

Blow-by hose clip 2 Hose coupling clamp at throttle body end 1.2 Throttle body retaining screw 2 Hose coupling clamp at airbox end 1.1

Fuel system, Canister

Clamp between throttle body and engine 2

Fairing

Windscreen to headlight fairing screw 4x0.7

Mobile headlight fairing to subframe screw 6x1 5 Fixed headlight fairing to subframe screw 6 x1 5 Fixed headlight fairing stud bolt (sides) 6x1 4 LOCK 2 Instrument panel retaining screw 5x0.8 1.5

Upper LH/RH fairing to subframe screw 6x1 5 Upper RH fairing to frame screw 6x1 5 Latch retaining screw 6x1 5 LOCK 2 Under tail cover retaining screw 6x1 8

Tail guard retaining screw 6x1 8 LH rear side panel retaining pin 6x1 4 Lower RH fairing self-locking nut 5x0.8 5

Glove compartment cable end stop retaining 5x0.8 5 screw Air conveyor retaining screw 6 x1 6 Front fin clamp fixing nut 6x1 5 Latch cable adjusting nut 7x1 6

Lock retaining screw 6 x1 5 LOCK 2

Blow-by valve 40x1.5 40 Oil breather cap 40x1.5 40 Mesh filter duct plug 32x1.5 42 Oil temperature sensor ring nut 30x1.5 38 LOCK 4 Generator rotor nut 24x1 190* ENGINE OIL Crankshaft gear fixing nut 22x1 190 GREASE B Oil drain plug 22x1.5 42 Oil mesh filter 22x1.5 42 Oil filler plug 22x1.5 5* Dr y clutch drum nut 20x1 190* GREASE B Crankshaft blanking cap 20x1 Fully home with tool THREE BOND 1375B Gearbox drum locating screw 16x1.5 30 Oil filter nipple 16x1.5 42 LOCK 2 or

                                                                    THREE BOND 1324

Oil cartridge filter 16x1.5 11 Engine oil on seal Mesh filter duct plug 15x1 20 LOCK 5 or

                                                                    THREE BOND 1375B

By-pass pump plug 15x1 25 LOCK 5 or

                                                                    THREE BOND 1375B

Ring nut for belt rollers on lay shaft 15x1 71 GREASE A Ring nuts for belt rollers on heads 15x1 71 GREASE A Generator cover sight glass plug 15x1 20 THREEBOND 1215 Timing layshaft gear nut 14x1 55* GREASE A Oil cooler setting plug 14x1.5 24 LOCK 5 or

                                                                    THREE BOND 1375B

Oil cooler nipple 14x1.5 24 LOCK 5 or

                                                                    THREE BOND 1375B

Pick-up inspection screw 12x1 15 LOCK 2 or

                                                                    THREE BOND 1324

Oil temperature sensor 12x1.5 18* LOCK 4 Spark plugs 12x1.25 20

                                                10x1.5        15    GREASE C

Head nuts: 1st snug torque

             2nd snug torque                                  25 (min. 23 max. 27)
             final torque                                     40 (min. 38 max. 42)
                                                10x1          20 (min. 19 max. 21) GREASE B

Con-rod bolts: 1st snug torque

                                                              35 (min. 33 max. 37)
                 2nd snug torque
                 final torque                                 67 (min. 66 max. 73)

Oil pump duct plug 10x1.5 Fully home with tool LOCK 5 or

                                                              15    THREE BOND 1375B

Head stud bolts 10x1.5 25* LOCK 2 or

                                                                    THREE BOND 1324

Pressure switch 10x1 19 Nipple for oil delivery to heads 10x1 15 LOCK 2 or

                                                                    THREE BOND 1324

Reduction bushing 10x1 LOCK 5 or

                                                                    THREE BOND 1375B
                                                                                      

Spark plug 10x1 15 Neutral light switch 10x1.25 10 Clutch-side casing service plug 10x1.5 15 LOCK 5 or

                                                                    THREE BOND 1375B
                                                                                     

Crankshaft dowels 8x1.25 13 THREE BOND 1375B Gearbox pawl screw 8x1 25 Gear stopper screw 8x1.25 18 LOCK 2 or

                                                                    THREE BOND 1324
                                                                                     

Oil delivery drilled screw 8x1.25 15 Intake and exhaust flange stud bolts 8x1.25 15 LOCK 2 or

                                                                    THREE BOND 1324

Intake manifold nuts 8x1.25 23

Oil pump screws 8x1.25 26 Casing jointing screws: 1st snug torque 8x1.25 19 (min. 17 max. 21) GREASE B

                         final torque                         25 (min. 22 max. 28)

Casing drilled screw 8x1.25 20 GREASE B Fixed tensioner 8x1 20 LOCK 2 or

                                                                    THREE BOND 1324

Mobile tensioner 8x1.25 26 LOCK 2 or

                                                                    THREE BOND 1324

Ground screw 8x1.5 13

Fluid collector breather screw 8x1.25 2.2 Stator cable bracket retaining screw 6x1 10 LOCK 2 or

                                                                    THREE BOND 1324

Starter motor screws 6x1 10 LOCK 2 or

                                                                    THREE BOND 1324

Starter idle gear pin screw 6x1 10 LOCK 2 or

                                                                    THREE BOND 1324

Generator stator retaining screws 6x1 10 LOCK 2 or

                                                                    THREE BOND 1324
                                                                                     

Flywheel / rotor screws 6x1 13 LOCK 2 or

                                                                    THREE BOND 1324

Gearbox bearing stop plate screws 6x1 10 LOCK 2 or

                                                                    THREE BOND 1324
                                                                                     

Head service screws (aluminium) 6x1 3 LOCK 2 or

                                                                    THREE BOND 1324

Intake manifold-fuel pump union 6x1 2.5 LOCK 2 or

                                                                    THREE BOND 1324

Bosch pick-up retaining screws 6x1 10

Batter y mount lower fastening stud bolt 6x1 10 LOCK 2 or

                                                                    THREE BOND 1324

Gearbox pawl screw 6x1 10 LOCK 2 or

                                                                    THREE BOND 1324
                                                                                                     

Inspection cover screws 6x1 4.5* Rocker arm shaft cover screws 6x1 10 Intake / exhaust valve cover screws 6x1 10 Casing jointing screws 6x1 10

Clutch cover screws 6x1 10

Generator cover screws 6x1 10 Clutch spring screws 5x0.8 5* GREASE A Manifold nipple 5x0.8 3 LOCK 2 or

                                                                    THREE BOND 1324

Split belt roller flange retaining screws 5x0.8 5* Cam cover plug 5x0.8 2.5* Screws 10x1.5 45 Screws 8x1.25 25 Screws 6x1 10 Screws 5x0.8 5*